For a straight, regular stitch, this mean to line up the edges and put the outside or fashion parts of the fabric together. Beginning at one edge of the fabric, push the needle through both layers of the fabric and pull until the knot at the end of the thread catches. Push the needle back through both layers of the fabric on the same side that the thread is currently coming through. Push it back through the fabric about one to two millimeters from the first hole. The smaller the stitches are, the more secure the seam will be.
Use the 1.0mm opening for 1.6mm fiber. Also trim the Kevlar to the ‘C’ length using the electrician style scissors. * Using the marker pen and the template card provided, measure and mark the buffer strip length as shown on the template. * Using the buffer strippers, strip off the buffer in at least two pieces. * Using a dry, lint-free wipe; Remove any remnants of the protective coating on the fiber after stripping the buffer.
I would then untwist the wires and put them in the correct color order that I need. Then I would flatten out the wires and in one hand hold my RJ-45 connector and then with the other hand feed the wires into the connector. This is usually pretty simple with the way the connectors are made, and they are also usually clear. After I’m sure that the wires are in the connector all the way, and in the right order, I would use a wire crimper to clamp[ the wires securely in to the connector. Coaxial cable- For the COAXIAL CABLE I would do the same first few steps by getting the correct length of cable that I would need.
The pH level is an indicator of: a) sedimentation b) filtration level c) oxygen levels d) whether a solution is acid or alkaline 35. Clarifying shampoos contain acidic ingredients that: a) reduce dandruff c) are always a good idea b) decrease shine d) cut through product buildup _____ _____ 36. If your client has a dry scalp, the condition may be helped by a: a) hair mask c) protein treatment b) detangler d) scalp conditioner _____ 37. The best method for hair brushing is to: a) brush random areas c) brush the scalp vigorously b) part it into sections d) focus on the ends _____ 38. When you elevate the hair below 90 degrees, you are: a) creating curl c) building weight b) layering the hair d) removing weight _____ 39.
It keeps you warm, it is perfect for outwear and keeps your body heat. Without proper fleece made from polyester, you can lose a lot of body heat and you will feel cold and unprotected. It is light on weight and you can put a spare in your rucksack. Base layer (thermals) – the base layer could be a t-shirt or a long sleeve shirt. It dries quickly, it is very light on weight, you can actually squeeze it, if it is wet and it will dry immediately.
4. The reason for the national policy for colour coding of cleaning equipment is to ensure that the same cleaning equipment is not used in multiple areas, therefore reducing the risk of cross-infection. Outcome 2 1. The three steps of the decontamination process are cleaning, disinfecting and sterilisation. Disinfecting is a process used to reduce the number of micro-organisms to a safe level for a defined procedure but which may not necessarily inactivate all viruses and bacterial spores.
It was very effective because the researcher has control over how much water is being squeezed out. * Rubber band- Used to secure the piece of paper towel to the glass bowl. This worked because a rubber band has stretching abilities when it comes to securing the paper towel. * An assistant- To assist with the
The thread had to be tightly woven and very durable. The clothes were used all the way to the end -- the parts that were worn-out and broken were mended and patched. When the piece of clothing was totally worn-out, the good parts were used again. This might be a reason why the archaeological findings are mostly church textiles. The looseness of the clothes was received by the using of gussets which were triangular inserts used to expand clothing.
Then, begin to wrap the right loop around the left loop to end up in front. Start to feed the right loop into the hole that has just been made. This is really the same as if you were tying a regular shoelace knot, except that you are working with a loop instead of a loose end. Finally, with the right loop now through the hole, grab hold of both loops and start to pull the knot tight. Notice that the loose end of the right loop drops back down to the front left, making the finished
One should make sure that the surface on which artificial turf has to be covered needs to be cleaned and smooth. Applying a self-leveling compound for removing surface imperfections, is primarily a good idea if the heap of grass you are laying is low. 2. Spread the commercial synthetic grass onto the clean and leveled area you wish to cover. For deriving a perfect edging, permit around 50 mm of grass on each side of the area for trimming off.