For this hair the mane brush will be used. To use the mane brush, brush the hair as if it were human hair. After the mane is tangle free, the hooves are ready to be cleaned out. For this particular task the hoof pick will be used. Face the rear end of the horse and stand parallel to his leg.
This is where the end of the line will be going to form the knot. Take the end of the line and very, very, carefully, thread it through the hole. Now grab the end of the line with one hand, and simultaneously, pull the other end of the line tight. All that is left to do now, is trim the excess line off the end with a pair of nail clippers, and add the
There are a few simple steps to getting ready. Step 1: First, you must tie your horse so she is ready for brushing. Step 2: Second, you must brush and make sure she looks physically ready to go out for a ride. sugar Step 3: Once brushed, you can place saddle blanket on her back and prepare saddle for placement. Step 4: Place saddle on back and look it over for any damage or issues that could pose a safety risk.
Unit 8 Lab 1 Running head: FIBER OPTIC CONNECTOR ASSEMBLY Fiber Optic Connector Assembly NT1310 Fiber Optic Connector Assembly * Figure 1 Fiber Termination kit Figure 1 Fiber Termination kit Figure 2: LC Multimode & Singlemode Connector Figure 2: LC Multimode & Singlemode Connector Put on safety glasses and prepare work area by organizing all necessary tools from the Fiber Termination Kit and the Consumables Kit. Place primer bottle into primer stand, remove dust-caps from fiber connectors, etc. * Slide the strain relief boot (and crimp sleeve for jacketed fiber) over the fiber in the proper orientation. * Using the jacket stripper tool, strip off the outer jacket at the ‘A’ length indicated on the template card. Use the 1.0mm opening for 1.6mm fiber.
Pick up the razorblade lightly, press down on each wire, moving with the grain along the wire to remove the insulation; do this in till no more comes off. Take the new jack and unscrew it; there will be two or three places to put the wires depending if the
Just because it is clean doesn’t mean that it is ready to run. Once you have cleaned everything it is time to take things apart by separating the two ends from the chassis. This will let you inspect the suspension and bulk heads more easily. You are mainly checking the shocks for pressure and the wheels and axial for binding and fluidity. It is important to make sure all the screws are tight, especially along the axil.
Introduction: Do any of you have that one pair of leather shoes or boots that you absolutely love? (Look around room) For me, its cowboy boots, and lots of them! A good shoe polishing technique will not only help them look their best, but also extend the life of them. I’m going to show you that shoe polishing is really easy to do once you have the right materials. Transition: Today, we will begin by gathering the supplies we need to polish our shoes.
The next step is to straighten the knees, while being careful not to lock them, as this could lead to fainting. Once the knees are straightened, line up the hips up with the ankle bones. To test if they are lined up, push them all the way forward and then all
Now you are ready to close the mouth which can be quite tricky sometimes, if all goes well and the jaw bones are still strong then a tack is put in the top of the mouth and one in the bottom and then tied together. If the bones are not strong then you would suture the mouth closed, you would do this by getting a piece of ligature and a needle, tie a not at the end of the ligature go up throw the nose cavity and back down and then down throw
Also, you need to insert the lens by using the forefinger on your opposite hand, and holding up your upper eyelid to prevent you from blinking. Then you have to use the third finger on the hand in which you have the contact lens to hold down your lower eyelid. After that, you need to look up and place the contact lens onto the white of your eye and look downwards to allow the lens to slip into position. Then you can remove your fingers and close your eye momentarily. And if you feel uncomfortable after wearing contact lenses, you have to remove them, and do all these processes over again.