d. Kilobyte 3. Which answer lists the correct number of bits associated with each term? c. 64 bits per quadruple wor 4. Which of the following answers are true about random-access memory (RAM) as it is normally used inside a personal computer? (Choose two answers.)
b,c 2. A PC NIC and a switch port create one electrical circuit to use when sending data. The sender creates a (maximum) 1-volt electrical signal with a frequency of 1000 hertz. Which of the following facts are also true? (Choose two answers.)
An actuator arm 13. Which of the following are components of an internal hard disk drive (HDD) (Choose two)? Actuator Arm Platters 14. Which of the following technologies are considered to be solid state? (Choose Two) RAM USB Flash drive 18.
Place-and-route or fitting is the process where the logic structures described by the netlist are mapped into the actual structure of the specific target device. This results in an output called a bit stream SECTION 1-6 26. 27. DIP pins go through holes in a circuit board. SMT pins connect to surface pads.
NT1110 Computer Structure and Logic Chapter 6: Memory and Storage 1. A computer storage location that allows information to be stored and accessed quickly from random locations within the DRAM (Dynamic Random Access Memory) on a memory module. 2. A page file is stored on the computer hard drive that is used as a temporary location to store information that is not currently being used by the computer RAM. 3.
(Choose two answers.) a. Used for short-term memory b. Used for long-term memory c. Used to process data d. Connects to the CPU over a bus using a cable e. Is installed onto the motherboard 5. This chapter describes the concepts behind how a CPU reads the contents from RAM.
Click Start, and then click Computer. Under Hard Disk Drives, right-click a drive, and then select
Are the computers in the same network? *Yes they are in the same network 14. List all the possible routes from Router B to Router D in the network shown in # 13. *B-A-E-D & B-E-D 16. List the subnets attached to Router C in Figure 6-21.
The AMD SB710 Southbridge chipset is used with Socket AM3/AM2 Processors, AMD Turion™ II Neo | AMD Athlon™ II Neo Processors (ASB2),AMD Turion™ Neo, AMD Athlon™ Neo and AMD Sempron™ Processors (ASB1). Its purpose on the motherboard is to control the processes that are going on within the computer's main frame system. 3. The Socket AM3 Connector is used with the same AMD SB710 Task 3 procedure 1. PROCESSORS | CLOCK SPEED | INTERAL CACHE | BUS SPEED | ARCHITECTURE | i7 | 2 GHz-3.5GHz | 6MB-8MB | 5GT/s | X86 | i7 mobile | 1.7GHz-2.9GHz | 4MB-8MB | 5GT/s | X86 | i5 | 2.3GHz-3.4GHz | 4MB-6MB | 5GT/s | X86 | i5 mobile | 1.3GHz-2.8GHz | 3MB | 5GT/s | X86 | i3 | 2.9GHz-3.6GHz | 3MB-4MB | 5GT/s | X86 | i3 mobile | 1.3GHz-2.8GHz | 3MB | 5GT/s | X86 | vPro | 2.0GHz-3.6GHz | 4MB-8MB | 2.5GT/s-5GT/s | X86 | vPro mobile | N/A | N/A | N/A | N/A | Xeon 7000 | 1.8GHz-3.5GHz | 2MB-24MB | 666MHz-6.4GT/s | X86 | Xeon 5000 | 1.6GHz-3.7GHz | 4MB-12MB | 666MHz-6.4GT/s | X86 | Xeon 3000 | 1.8GHz-3.4GHz | 2MB-12MV | 1066MHz-6.4GT/s | X86 | Itanium 9000 | 1.4GHz-1.6GHz | 6MB-24MB | 533MHz | X86 | Pentium | 2.2GHz-3.3GHz | 2MB-3MB | 5GT/s | X86 | Celeron | 1.6GHz-2.9GHz | 512KB-2MB | 800MHz-5GT/s | X86 | 2.
1.04 Motherboards: This video explained what ATX, BTX, and NLX form factors are and determined the differences between the three. It also explained what communication buses are. It explained what 8 and 16-bit ISA’s are. It explained what PCI, PCIx, PCIe, and AGP slots are. 1.