Now that you have everything out of the way we can get started on tuning this engine up. First you start with number one cylinder, which is on the driver side front of the engine, remove the rubber boot from the first spark plug and mark it with a marker showing its number one next take your socket and ratchet and unscrew the plug from the side of the head. The plugs we choose are pregapped so we wont have to gap them carefully install the new plug in to he head make sure you don’t hit the electrode on the tip of the spark plug tighten it to approximately 35 inch pounds. Next follow the plug wire that you removed back to the distributer and remover the rubber boot from that point match that wire with one of the new ones as close as possible mark that wire as cylinder 1 and mark the distributer cap where you took that one off. I like to continue on the odd side of the vehicle so we’ll head to cylinder number 3.
Unit 6 Exercise 1 Connector Installations Twisted-pair cable: Step 1: Measure the cable you want to put ends on and trim it to the proper length using the cable cutter. Step 2: Use the cable stripper to strip about 1.5" of the jacket from the end of the cable. Then, rotate the stripper around the cable twice. This will cut through the jacket. Step 3: Remove the stripper from the cable and pull the trimmed jacket from the cable, exposing the inner conductors.
1. F –The COS verifies the AOF during emplacement using the CSD 2. T –The suspension lever should always mirror the position of the howitzer 3. F –The M577 fuze is compatible with the M107 projectile 4. F – The M107 projectile is the only HE round authorized by the US Army 5.
After ejection, the WP-saturated felt wedges in the payload fall to the ground in an elliptical pattern. Each wedge then becomes a point or source of smoke. The M825 is ballistically similar to the M483A1 (DPICM) family of projectiles. Employment. Smoke is employed by using the quick smoke and immediate smoke techniques.
M4/M4A1 CARBINE’S WEEKLY MAINTENACE SOP AFCZ-XYZ 123-456 24 April 2014 1. Purpose: Third Platoon will be conducting clearing, disassembling, cleaning, inspection for serviceablity, lubricating and reassembling of the carbine. 2. Applicability: Third Platoon, Alpha Company, 1-10 ATK 3. References: A. Lubricate order (LO).
Disc-brake consists of a disc bolted to the wheel hub and sandwiched between two pistons and friction pads supported in a calliper fixed to the stub-axle. When the brakes are applied, the pistons clamp the friction pads against the two side faces of the disc. 4. Drum-brake this consists of two brake-shoes and lining supported on a back plate bolted to the axel-casing. These
DEPARTMENT OF THE ARMY REGIMENT FORT BLISS, TX 79916 PROCEDURES FOR THE WEEKLY MAINTANANCE OF 3RD PLATOON’S M4 CARBINE’S AFVA-BCX 14 JULY 2014 SOP Number 1 1. REFERENCES: a. Lubricate order (LO) b. STP 21-1-SMCT c. TM 9-1005-319-10 d. DA FORM 2404, Equipment Inspection and Maintenance Worksheet 2. PURPOSE: To establish uniformity of the cleanliness, mainanenance, and inspection for all 3rd Platoon’s M4 carbines 3. APPLICABILITY: This applies to all personnel assigned to 3rd Platoon, Bravo Company. 3.
Pick up the razorblade lightly, press down on each wire, moving with the grain along the wire to remove the insulation; do this in till no more comes off. Take the new jack and unscrew it; there will be two or three places to put the wires depending if the
(See figure 1.1.) Figure 1.1 3) Use the masking tape to keep the cone closed. At the closed end of the cone (the bottom), use extra masking tape to cushion the blow from the fall AND weight the bottom. This will insure that the cone falls bottom side first. 4) Next, we will construct a box that is a little larger than the egg with the remaining poster board.
The LCD displays message as “wheel chair is turning right” and red LED turns ON to indicate wheel chair is turning right Finally when 4th finger is bent the output from 4th sensor exceeds threshold limit. This time micro controller rotates all four motors reverse. So wheel chair moves reverse. The LCD displays message as “wheel chair is moving reverse” and yellow LED turns ON to indicate wheel chair is moving