The following data were obtained when a sample of barium chloride hydrate was analyzed as described in the Procedure section. Calculate (a) the mass of the hydrate, (b) the mass of water lost during heating, and (c) the percent water in the hydrate. Mass of empty test tube 18.42 g Mass of test tube and hydrate (before heating) 20.75 g Mass of test tube and anhydrous salt (after heating) 20.41 g. Mass of the Hydrate is 2.33g. Loss (H2O) is 0.34g. Percent H2O in Hydrate is equal 0.34/2.33=14.6% 3.
Developed TLC plate by placing plate in chamber not contacting filter paper.7. Removed plate from chamber when solvent front was 1 to 2 cm from top of plate.8. marked solvent front with pencil line & set on paper towel to dry.9. Marked position of compounds on plate using a UV lamp10.Calculated Rf values for each spot11. determined results were unsatisfactory to how experiment was supposed to turn out.Part B1.
Make sure the rubber stopper is securely in place since gas can easily leak out. Collecting the gaseous product: Prepare the gas collection bottle by positioning the bottle so that its mouth is. directly over the hole at the bottom of the trough; this is where the gas will enter the bottle. After the reaction, slide a square of glass over the mouth of the bottle while the bottle is still under water. Keeping the glass fixed to the mouth, raise the collection bottle and invert.
pyridinium hydrobromide perbromide type of stationary phase column length column temperature rate flow of the carrier gas List the 4 general factors that affect the separation obtained on a gas chromatograph What specific technique is used to collect/isolate your purified unknown compound at the end of the recrystallization experiment? suction filtration 14 of 22 4/16/12 9:15 PM StudyBlue Flashcard Printing of Lab Final 2211L UGA
10/8/13 Lab Report Introduction The purpose of the experiment was to do three different reaction and calculate the enthalpy change of the reaction with Hess’s Law. Then compare your calculated results to the results from the experiment. Experimental Design Materials: Vernier computer interface Computer Temperature Probe Two styrofoam cup 100 mL graduated cylinders Glass stirring rod 2.0 M Hydrochloric acid, HCl, solution 2.0 M Sodium Hydroxide, NaOH, solution 2.0 M Ammonium Chloride, NH4Cl, solution 2.0 M Ammonia, NH3, solution Ring Stand Utility Clamp Fume hood or well-ventilated room Magnetic Stirrer Paper Lid Procedures: Use proper lab safety and wear safety glasses, and make sure in well-ventilated room. Connect the temperature probe to the Vernier interface in the Channel 1 port. Then connect interface to the computer using the USB cable.
Name: ___________________________________ Date: ______________ Practice Test #3 ____ 1. When a precipitation reaction occurs, the ions that do not form the precipitate A) evaporate B) are cations only C) form a second insoluble compound in the solution D) are left dissolved in the solution E) none of these 2. An aqueous solution of potassium chloride is mixed with an aqueous solution of sodium nitrate. The complete ionic equation contains which of the following species (when balanced in standard form)? A) B) C) D) E) ____ 3.
It's important that the toy is cleaned and sanitized properly to maintain an antibacterial and antimicrobial surface as well as the interior. It's pretty dangerous to leave bodily fluids on the toy without cleaning it. When it comes to the Fleshlight, there are pockets, ridges and bumps inside where fluids can stick. A quick
n (3) Solutions of aqueous sodium hydroxide and hydrochloric acid react to form water and aqueous sodium chloride. co NaOH(s) → Na+(aq) + OH–(aq) ∆H1 = ? Chemistry with Vernier py In this experiment, you will use a Styrofoam-cup calorimeter to measure the heat released by three reactions. One of the reactions is the same as the combination of the other two reactions. Therefore, according to Hess’s law, the heat of reaction of the one reaction should be equal to the sum of the heats of reaction for the other two.
Let’s call this number X. Then the structural formula of BaCl2 hydrate can be written as BaCl2•XH2O. The reaction of dehydration is |BaCl2•XH2O ( BaCl2 + XH2O |(5) | According to the stoichiometry of the reaction (5) |[pic] |(6) | Where N1 is the number of moles of BaCl2 formed in the reaction (5) and N2 is the number of moles of water lost in the reaction (5). To find out N1 you need to divide the mass of BaCl2 after the reaction by its molar mass. To find out N2 you have to determine the mass of water produced in the reaction.
Fractional distillation [edit] Laboratory setup Fractional distillation in a laboratory makes use of common laboratory glassware and apparatuses, typically including a Bunsen burner, a round-bottomed flask and a condenser, as well as the single-purpose fractionating column. [edit] Apparatus Fractional distillation apparatus using a Liebig condenser. A conical flask is used as a receiving flask. Here the distillation head and fractionating column are combined in one piece. [1] * heat source, such as a hot plate with a bath, and ideally with a magnetic stirrer.