6. Why should all duct work designs start with an accurate heat load study? (57.1) Proper duct system designs are critical to the energy efficiency of a building. 7. Explain the function of the following duct components: (57.2) Ell are elbows used to make turns in ductwork, Wye is used to split one large duct into two smaller ducts, Transition is used to change rectangular ducts from one size to another, Boot is used at the end of a round duct to allow connection of a rectangular register or grill.
This colligative property is important in many industries, but is clear to see when using ordinary salt to remove ice from steps or a driveway. The water takes salt into solution, which in turn lowers the freezing point of the water, ensuring that even sub-freezing ambient temperatures do not lead to ice buildup anywhere the salt or ice melt was applied. Experimental Procedure: Before any measurements were taken, equipment was set up and calibrated. Using Microlab’s integrated calibration file the thermistor was calibrated in order to obtain accurate temperature measurements. A graph for the data was also set up with time on the x axis in .5 second intervals and temperature on the y axis.
The salts will be dissolved in distilled water by small quantities until the reaction reaches When ionic compounds dissolve in water, they either absorb energy from or release energy to the surroundings. If a chemical reaction absorbs heat from the surroundings, it is an endothermic reaction. If a solution releases heat to its surroundings, it is an exothermic reaction. The enthalpy of dissolution is the enthalpy change associated with the dissolution of a substance in a solvent at a constant pressure. The change in enthalpy relies on the concentration of the salt solution, because different concentrations will produce different enthalpies.
Name: 6.03: Calorimetry Data and Observations: Part I: Insert a complete data table, including appropriate significant figures and units, in the space below. Also include any observations that you made over the course of part I. (4 points) I observed that when the metal is placed inside the calorimeter, it transfers heat to the water making the water increase temperature while the metal will decrease temperature. I also noticed that the system was the metal and the surroundings is the water, this is because the water is taking in the heat from the metal making the water warm. Metal Name Mass of Metal Volume of water Initial temp.
This will occur because the water and glucose are small enough to diffuse out of the pores in the dialysis bag, but the starch molecules are too large to fit through 2. If a solution is very hypertonic, then the most amount of water will diffuse across the semi-permeable membrane into the dialysis tubing. This occurs because the higher concentration of solute, the more water it takes to reach equilibrium, thus, the faster rate of osmosis. 3. If we place the potato in a sucrose solution with a similar solute concentration as a potato, then the least amount of water will diffuse into or out of the potato cells.
Hydrate Lab The purpose of this lab is to analyze the percent water in a crystalline hydrate and to indentify the hydrate from a list of possible unknowns. The solid hydrate will be heated to remove the water, and the percent can be found by measuring the mass of the solid before and after heating. The hydrate will be indentified by comparing the percent water in the hydrate with the percent water calculated for the possible unknown. Before the lab there are pre-lab questions: 1. Describe the three general safety rules for working with a Bunsen burner.
This hypothesis was chosen because it’s easier to digest hot water than it cold. Materials and Methods There were multiple materials and methods used for this particular latent lab. For example, the groups used the hot plate to heat up the water to different temperatures. Another material that was used was the thermometer used to check the temperature
Volume of acidic solution Volume of the water was measured in a graduated cylinder. More acidic solution will result in higher rates of corrosion and vice versa Time in acidic solution A stopwatch was used to measure the amount of time each sample was kept in the solution The amount of corrosion will increase as the sample is kept in the solution for longer periods of time. Temperature of Room The temperature of the AC was regulated to be constant. The temperature can affect the rate of the reaction, which in turn will affect the experiment. Procedure: • Cut each sample of marble sample must be cut into equal pieces and must be then measured to match a weight of 50g in the weighing
The energy in the radiator is transferred to the air. Explain the factors that affect the rate of energy transfer in the engine and radiator. • The rate of energy transfer depends on the temperature difference between the system and the surroundings • Bigger the temperature differences between the radiator and the air, faster the rate of energy transfer. • Radiator contains water which has a very high specific heat capacity. So it can absorb a large amount of heat from the engine • Both the radiator and engines are made of metal which makes both of them good conductors of heat.
So, it makes sense that the speed of sound has the same order of magnitude as the average molecular speed between collisions. In a gas, it is particularly important to know the temperature. This is because at lower temperatures, molecules collide more often, giving the sound wave more chances to move around rapidly. At freezing (0º Celcius), sound travels through air at 331 meters per second (about 740 mph). But, at 20ºC, room temperature, sound travels at 343 meters per second (767 mph).Liquids:Sound travels faster in liquids than in gases because molecules are more tightly packed.