NT1230 Unit 2. Assignment 1. Disk Redundancy Research Using the Internet and the ITT Tech Virtual Library, research the following questions, and provide your thoughts on each one. Submit your answers in a Word Document and ensure that you cite any resources you utilized with the proper APA format. 1.
Follow all necessary steps as given in the documentation; you would now have generated a “.hex” file which you can load into the microcontroller. 4. You can load the “.hex” file by using Bootloader; steps for installing and using Bootloader is given in Refer section 2.6 (page 29) of the Software manual for complete instruction of using the AVR Bootloader on your system. Step number 5 and 6 will be same explained above in option 1. If Teams get doubts while taking the tutorial, they can post the queries on e-Yantra QuestionAnswer forum at
4.4.3 Noise SMF Crosstalk Coaxial Interference Coaxial Op en (Open Circuit) UTP Short (Short Circuit) MMF Break UTP 4.4.4 I first start with my anti-virus to run any scans, after that I go into my device manager and click the network adapter. I then will go into my general tab and click trouble shoot. 4.4.5 Some of the common strategies for trouble shooting from top down starts with are you able to view a web page in your browser, can you se nd or receive email and/or are your username and password correct, and are your Interne t Explorer connection settings correct. If none of those are an issue you take it a little further. Is there a firewall configured on your computer, is your firewall block ing ports, if you turn off the firewall does it resolve your problem?
2. Which of the following standalone devices can be found near the Internet edge, with a primary purpose of providing some type of network security between an enterprise or SOHO TCP/IP network and the Internet? (Choose two answers.) a. LAN access point b. IPS c. Analog modem d. Firewall Answer: B, D. A firewall normally sits inline, in the packet-forwarding path, choosing which packets to allow and disallow. An intrusion prevention system (IPS) can sit inline or outside the packet-forwarding path, reporting on complex attacks based on combinations of events.
iLab Grading Rubric Category | Points | Description | Section 1Converting Decimal to Binary and Binary to Decimal—20 Points Total * Task 1 * Task 2 * Task 3 * Summary Paragraph | 8 228 | Perform the indicated conversions and post the required problems to your answer sheet.In your own words, summarize what you have learned concerning network commands available within the Windows operating system. | Section 2Classifying Network Addressing Lab—20 Points Total * Task 1 * Task 2 * Task 3 * Task 4 * Problem 1 * Problem 2 * Summary Paragraph | 1.21.26.61.81.28 | Required ScreenshotAnswer the question or provide the required observation when requested.In your own words, summarize what you have learned about the Network Monitor. | Total | 40 | | ------------------------------------------------- Name: Charley Baskett Date: 08/16/2013 Professor: Biao Jiang ------------------------------------------------- Converting Decimal to Binary and Binary to Decimal (20 points) Instructions for the Binary Conversion Exercise: NOTE! YOU DO NOT HAVE TO CLICK ON THE DIAGRAM TO START THE LAB. The diagram displayed during the experiment is not used.
This password is stored in _______. BIOS CMOS RAM* DDR RAM the CPU 8. (TCO 3) The term form factor in regards to a motherboard refers to the ______ layout of the components on the board physical logical proposed inverted 9. (TCO 9) When you first purchase a notebook, make sure you have a ____ CD containing the installed OS so you can recover from a failed hard drive development management diagnostic recovery 10. (TCO 9) ____ let you specify which devices are to be loaded on startup for a particular user or set of circumstances Hardware profiles* Folder redirections Briefcase profiles Startup profiles 11.
Take a screen shot of the Network Map window by pressing Alt+ Prt Scr, and then paste the resulting image into the Lab03_worksheet file in the page provided by pressing Ctrl + V. * Exercise 3.3 | Manually Configuring TCP/IP | Overview | Because the lab network you are constructing for Contoso, Ltd. must be isolated from the production network, you do not want lab computers to obtain their TCP/IP settings from the DHCP servers on the production network. Therefore in Exercise 3.3 you manually configure the TCP/IP client to use static IP addresses. | Completion time | 15 minutes | 3. Using the information in the IPconfig.exe
Routers R1 and R2 are directly connected via their serial interfaces and are both running the EIGRP routing protocol. R1 and R2 can ping the directly connected serial interface of their neighbor, but they cannot form an EIGRP neighbor adjacency. What action should be taken to solve this problem? Configure both routers with the same EIGRP process
Which of the following is a Windows command-line utility for seeing NetBIOS shares on a network? * c. Net view 29. To view eDirectory information on a NetWare 5.1 server, which of the following tools should you use? * d. Novell Client 30. The Nbtstat command is used to enumerate *nix systems.
(TCO 8) A programmer makes a connection between a Visual Basic application and a database using the _____. (Points : 5) Database Integration tool data box control Data Source Configuration Wizard Dataset Designer Question 14.14. (TCO 9) The components of a two-tier architecture are _____. (Points : 5) the primary and the secondary the client and the server the master and the subordinate the alpha and the beta Question 1. 1.