(8) Pull the charging handle to the rear and release it, allowing the bolt to return to the full forward position. (9) Place the selector lever on SAFE. (10) Close the ejection port cover. b. Disassembling (1) Remove the sling. (2) Remove the handrails.
If the driver doesn’t have a manual, just find the sturdiest point closes to the tire you are changing. With the jack in place, take the handle and turn the crank on the jack clock wise to start lifting the car up until the wheel is high enough off the ground to remove the tire. Once the car is off the ground, finish removing the lug nuts and place them in the hub cap. By placing the lug nuts in the hub cap, the driver will know exactly where they placed them. Remove the wheel from the vehicle placing it flat on the ground to
The final steps of fixing a flat tire are tightening the lug nuts by turning them clockwise until they are nice and snug. After they are all nice and snug, lower the vehicle to the ground, take out your crossbar and tighten all the lug nuts. When everything is tightened, place all your tools back from where you
Drop the magazine, if there is one in the rifle, by pressing the magazine-release button on the left side of the weapon. Pull back the charging handle and look inside the breech to check for any rounds in the chamber. If there is brass or a live round caught in the breech then lock the bolt to the rear and carefully pry it out. This is a very important step. You need to make sure that your weapon is clear of any rounds.
Next, turn off your engine and engage your parking break. Make sure to turn on your vehicles hazard lights, regardless of the time of day. This ensures that other drivers are aware of your presence. If in your possession, take an extra step of precaution and put up reflectors, also to alert other motorist you are stopped. Next, remove all supplies from trunk, or car.
CPU * surge suppressor motherboard hard drive 7) What are two examples of output peripheral devices? (Choose two.) * printer * speakers flash drive external DVD external modem 8) What two functions does a UPS provide that a surge protector does not ? (Choose two.) protects the computer from voltage surges * provides backup power from an internal battery protects the computer from sudden voltage spikes gives the user time to phone the electrical company * gives the user time to safely shut down the computer if the power fails provides backup power through a generator provided by the wall outlet 9) What is a word processor?
Separate the jumper cables making sure the clamps do not touch; it could cause a short circuit. Before clamping one of the red cables onto the positive terminal you may need to remove a plastic cover. After you have removed it or it was already removed, you can now attach the clamp to the positive terminal of the dead battery making
6- Place only the edge of the Q-tip at the top the Flame. 7- Remove it when you see the of light being given off to avoid burning the Q-tip. 8- Clean up procedure: Discard used Q-tips to the bin, cover back compounds and put them up in a safe place, pour away distilled water in the sink, disconnect the Bunsen burner and clean it if stained,clean the lab test surroundings with paper towel to ensure no stain is left, wash your hands remove your goggles only when all equipments have been placed in safe places. Compound | Flame Colour Observation | 1 LiNO3
This way you don't have long strings flopping around. Once all of the strings are cut, place the pliers on the pin. Wiggle out the pins that are holding the strings in place and pull up. Lay all the pins to the side of the guitar and then unravel the strings from the top of the guitar at the tuning keys. When all the strings are off, make sure to throw all the strings away into the trash.
Liquid items must be placed in clear plastic bags, this includes toiletries, make up, perfume and aftershave. Also all large electrical items must be removed from hand luggage beforehand. Coats, jackets, jumpers, high heels, belts, watches and metal jewellery must all be removed before going through x-rays. The UK once had a new method of screening passengers to further improve airport security using backscatter X-ray machines that provide a 360-degree view of a person, as well as "see" under clothes, right down to the skin and bones. They are no longer used and were replaced by millimetre wave scanners which shows any hidden items while not showing the body of the passenger.