Properties of Water Lab Part A. Observations: When Copper Chloride was mixed into water the Copper Chloride started as small crystals in the bottom and sides of the test tube, but once shaken they completely dissolved into the water. When Copper Chloride was dropped into the alcohol it seemed to clump together and sink to the bottom, when shaken lightly or even vigorously the crystals of Copper Chloride simply moved around but retreated back to the bottom of the test tube when left still, it did not mix at all. Questions: 1. When Copper Chloride is added to water and shaken vigorously the copper Chloride completely dissolves leaving a pale transparent blue solution. 2.
What amounts of stock solution and water do you need to use? (Remember that you will need enough solution to more than cover the egg.) p. Write up your new dilution procedure in your lab notebook, including the calculated salt concentrations for each cup. q. Make the new dilution series.
A voltmeter was used to measure the electrical resistance of different solutions. * Experiment and Observation: The plastic and glassware used in this experiment was thoroughly washed with hot water and rinsed with distilled water. * * Part I: Preparation of Standard Phosphate Solutions 1. 1.0 ppm standard: 1.00 mL of 10.0 ppm phosphate solution was placed in a 25 mL graduated cylinder and diluted to exactly the 10 mL mark with distilled water then poured into a plastic cup labeled 1. Cylinder was rinsed with distilled water.
An aqueous solution of ammonium sulfate is allowed to react with an aqueous solution of lead(II) nitrate. Identify the solid in the balanced equation. A) (NH4 )2 SO4 B) Pb(NO3 )2 C) PbSO4 D) NH4 NO3 E) There is no solid formed when the two solutions are mixed. ____ 11. An aqueous solution of sodium carbonate is reacted with an aqueous solution of calcium chloride.
6. Zinc Sheet: a rectangular, thin, sheet like metal, gray/silver. 6 5 4 3 2 1 * Solubility of solid iodine; 1. Solid iodine in 1 mL of water is slightly soluble, because the solution turns into a light brown/yellow color. However majority of the solid Iodine was left at the bottom of the test tube; which leads to the conclusion that it’s not reactive on water.
0.00079 moles EDTA4- c. 0.00079 moles ZnI2 d. 0.0517 grams of ZnI2 are in the sample e. 0.0517/0.237= 21.8% f. Error Is 6.34% Lab Report: Part 1: In this lab we used the following supplies: * Zinc Iodide * Na2H2EDTA(s) * Calmagite indicator solution * pH 10 buffer solution * 6M Acetic Acid * Unknown Zinc Compound The main purpose for this part of the lab was to determine the amount of zinc ion in a sample of ZnI2 by titration. The two types of zinc: * Zinc iodide made by zinc and iodine * Commercially purchased zinc iodide (the
Introduction: Thyme contains a surprising amount of iron compounds. This experiment enables us to determine the amount of iron(II) present in dried thyme by means of a redox reaction. Method: 1. Weigh accurately about 1g of dried thyme and put into a 250cm3 beaker. Record the mass of thyme used.
Using a Buchner funnel, a hose, and a suction flask we created a vacuum filtrator which we used to help remove the remaining liquid on the copper so that we may make a more precise measurement of the mass of the remaining copper. Our final mass of copper was .7951 grams. Results and Discussion: Initial Mass of Cu: .25 grams When we mixed the 5 ml of 6 molar HNO3 the copper had disappeared, indicating it had been used in the reaction. The copper had undergone a single replacement reaction and a decomposition reaction. Initial equation: Cu(s) + HNO3(aq) -> Cu(NO3)2(aq) + NO2(g) +H2O(l) Balanced: Cu(s) + 4HNO3(aq) -> Cu(NO3)2(aq) + 2NO2(g) + 2H2O(l) The copper had replaced the Hydrogen in the HNO3 and the NO3 had also broken down into NO2 and O2- allowing the H+ to bond with it and create
For zinc ion to react, the NaEDTA must also be an ion in the solution which means that the large salt must be dissolved in water. Procedure 1) Weighed out 3.64 of NaEDTA on an electronic beam balance 2) Added this mass of NaEDTA using wide mouth funnel to a 250 mL volumetric flask. 3) Rinsed the funnel with a squirt bottle containing deionized water making sure none of the solid remained in the funnel. 4) Added about 100-200 mL of deionized water to the volumetric flask containing the solid NaEDTA. 5) Swirled the solution until the NaEDTA (s) dissolved entirely.
The MgSo4 absorbed the last traces of water the ether solution. The solution was completely dry when it appeared crystal clear and MgSO4 floated in the liquid, when swirled. If solution is cloudy, more drops of MgSO4 were to be added until solution was completely dropped. 5) We decanted the solution from the solid MgSO4 into a 50 or 100 ml round bottom flask. 6) The ether was removed using the rotary evaporator.