Pour all the filtrate and washings into a 250cm3 volumetric flask. Make up to 250cm3 with 1.0mol dm-3 sulphuric acid(VI) acid. Stopper the flask and invert several times to thoroughly mix the solution. 5. Fill the burette with 0.005mol dm-3 potassium manganate(VII) solution.
After that, dissolve the sample in 2 mL of deionized water and shake the test tube for 1 to 1 ½ minutes to dissolve the solid. Place another dry test tube in a 50mL beaker and weigh it. Find a bottle of barium iodide and record the name and molar mass. Then, weight out either anhydrous barium iodide or barium iodide dehydrate into this test tube and dissolve is it in 2 mL of deionized water. Pour the contents of one of the test tubes into the other and a reaction should occur and you should see a white precipitate of barium sulfate form.
Obtain another 50-mL beaker and add 0.05g of Chromium(III) Nitrate to the beaker. Then, add 17 mL of distilled water and mix until the solid is dissolved. 3. Obtain a final 50-mL beaker and add 0.05 grams of the unknown substance to the beaker. Add 17 mL of distilled water and mix with a stir bar until the solid is completely dissolved.
Then 5mL of HCl was added to copper to completely remove all traces of zinc. Once the bubbling had stopped, the rest of the liquid was decanted away from the copper. Then the copper recovery set up was put together using tubing, Buchner funnel, filter paper and suction flask. Then the filter paper was weighed before placing it in the funnel and wetted down. The aspirator was turned to medium high, and then the copper was poured onto wetted filter paper.
Procedure 1. Begin to prepare an EDTA solution. Weigh out 3.62-3.64 g of NaH2EDTA and record exact mass. Add the weighed amount to a 250 ml volumetric funnel carefully using a funnel Wash the funnel with water to ensure all of the solid is delivered to the flask Add 100-200 ml of water and mix. Enough water should be added so that the flask is full to the 250 ml mark Tightly wrap the top of the flask with a Parafilm when finished 2.
A cuvette block, four cuvettes, three 50 mL beakers, one 150 mL beaker, and one 5mL pipet were obtained. The phosphate buffers NaH₂PO₄ and Na₂HPO₄ were procured weighing .4060g and .4106g respectively. The phosphate buffers were then transported to the 150mL beaker. Next 50mL of distilled water was measured using a graduated cylinder and added to the 150mL beaker. Twenty drops of bromothymol blue was also added to the 150mL beaker.
Cylinder was rinsed with distilled water. * * 2. 2.0 ppm standard: 2.00 mL of 10.0 ppm phosphate solution was placed in a 25 mL graduated cylinder and diluted to exactly the 10 mL mark with distilled water then poured into a plastic cup labeled 2. Cylinder was rinsed with distilled water. * 3.
c. Prepare the solution by dissolving 38.90 grams of ZnI2 with 500 mL of water. d. 0.0125/0.25 = 0.05 L = 50 mL. This produces 0.0125 moles of ZnI2 5. Exercise 5: a. (0.125)(0.1) = 0.0125 moles of solute b. Pour 50 mL of the stock solution to get the number of moles needed.
Then, 3.4 g of ammonium sulfate was slowly added to the supernatant 1 as it was stirred for 15 min to achieve 50% saturation (85g/L of solution). The supernatant was then centrifuged at 9000 x g and 40C for 15 min and 5 ml of the second supernatant was transferred to a conical tube. The obtained second pellet was resuspended in 4 ml of distilled water and transferred into another dialysis
Materials and Methods To begin, .4001 grams of Na2HPO4 and .4081 grams of NaH2PO4 solid was added together into a clean, dry 150 mL glass beaker. Then, approximately 50 mL of distilled water was added to the mixture, and the phosphate solids were stirred until fully dissolved. The last ingredient added to the beaker was exactly 20 drops of the liquid .04% bromothymol blue solution. Using the Vernier pH probe, the initial pH of this soluton was found to be 7.10. After obtaining three clean, dry 50mL glass beakers (Labeled one of each “yellow,” “blue,” and “green.”) approximately 5.00 mL of the solution from the 150mL beaker was added to all three with a volumetric pipet.