Part A: Spectroscopy 1. 0.05g of Iron(III) Nitrate in a 50-ml beaker. Add 17 mL of distilled water to the beaker and mix with a stir rod until the solid is completely dissolved. 2. Obtain another 50-mL beaker and add 0.05g of Chromium(III) Nitrate to the beaker.
After that, dissolve the sample in 2 mL of deionized water and shake the test tube for 1 to 1 ½ minutes to dissolve the solid. Place another dry test tube in a 50mL beaker and weigh it. Find a bottle of barium iodide and record the name and molar mass. Then, weight out either anhydrous barium iodide or barium iodide dehydrate into this test tube and dissolve is it in 2 mL of deionized water. Pour the contents of one of the test tubes into the other and a reaction should occur and you should see a white precipitate of barium sulfate form.
c. Prepare the solution by dissolving 38.90 grams of ZnI2 with 500 mL of water. d. 0.0125/0.25 = 0.05 L = 50 mL. This produces 0.0125 moles of ZnI2 5. Exercise 5: a. (0.125)(0.1) = 0.0125 moles of solute b. Pour 50 mL of the stock solution to get the number of moles needed.
BE READY WITH THE STOPWATCH. Record the time in the data table. Room Temperature Water: Fill beaker with 80mL of water. Use thermometer to record the temperature Drop Alka-Seltzer tablet in water. Measure the time it takes to completely dissolve.
Cylinder was rinsed with distilled water. * * 2. 2.0 ppm standard: 2.00 mL of 10.0 ppm phosphate solution was placed in a 25 mL graduated cylinder and diluted to exactly the 10 mL mark with distilled water then poured into a plastic cup labeled 2. Cylinder was rinsed with distilled water. * 3.
The following data were obtained when a sample of barium chloride hydrate was analyzed as described in the Procedure section. Calculate (a) the mass of the hydrate, (b) the mass of water lost during heating, and (c) the percent water in the hydrate. Mass of empty test tube 18.42 g Mass of test tube and hydrate (before heating) 20.75 g Mass of test tube and anhydrous salt (after heating) 20.41 g. Mass of the Hydrate is 2.33g. Loss (H2O) is 0.34g. Percent H2O in Hydrate is equal 0.34/2.33=14.6% 3.
ABSTRACT In the “Density, Accuracy, Precision and Graphing” experiment, the purpose was to determine the density of water and the concentration of a saline solution as well as to compare the accuracy and precision of a graduated cylinder and a graduated pipet. Based on the instructions of the lab manual, Fundamentals of Chemistry, the experiment was performed in three parts, Part A: Density of Water-The density of water was calculated by measuring the mass of three different volumes: 10mL, 30mL and 50mL. Part B: Accuracy and Precision was performed using a 100mL beaker, 10mL graduated pipet and deionized water. The experiment was performed three times; each time, 10mL of water was added to the beaker and recalculated. Part C: Density of Sodium Chloride (NaCl) Solution, a sample of NaCl was obtained and measured using a 100mL beaker and a 10mL pipet to determine the concentration of the solution.
Record data. 5. Place the beaker on the hot plate and carefully raise the temperature to 6® C and count the breaths the fish takes, record the data. 6. Repeat step 5, raising the degree by 3® each time until you reach 30 ® C. After every 3® increase, count number of breaths for 60 seconds.
Mix. k. Measure out 3/4 cup of the solution from cup 3 and add it to cup 4. Mix. l. What are the relative salt concentrations of cups 1–4? Example: Cup 2 is made up of half stock solution and half tap water, which is a 50 percent relative salt concentration.
This solution was placed in a burette and 18.4 cm3 was required to neutralise 25 cm3 of 0.1 moldm-3 NaOH. Deduce the molecular formula of the acid and hence the value of n. 5. Sodium carbonate exists in hydrated form, Na2CO3.xH2O, in the solid state. 3.5 g of a sodium carbonate sample was dissolved in water and the volume made up to 250 cm3. 25.0 cm3 of this solution was titrated against 0.1 moldm-3 HCl and 24.5 cm3 of the acid were required.