Using a measuring cylinder, add 50cm3 of 1.0mol dm-3 sulphuric(VI) acid to the thyme extract in the conical flask. 8. Titrate the solution in the conical flask with the potassium manganate(VII) solution until a pale pink colour persists for 10 seconds. 9. Repeat the titration until there are two titres within 0.1cm3 of each other.
Place 10 drops of zinc nitrate into A3 of the 24 well plate. 5. Place 10 drops of iron (III) chloride into A4 of the 24 well plate. 6. Place 10 drops of copper (II) sulfate into A5 of the 24 well plate.
Using another 125-mL flask, 60-mL of 0.3622 M potassium hydroxide in ethanol was deposited. Both flasks were clamped in a temperature-controlled bath regulated at 50.0˚C. The solutions were then set in the temperature bath for ten minutes to equilibrate. An empty 250-mL Erlenmeyer flask was also clamped in the same water bath. In another flask 50-mL of ice water was deposited with three-drop phenolphthalein.
Calculate the exact normality of Na2S2O3 knowing that in this chemical reaction 1 gram-equivalent of K2Cr2O7 react with 1 gram-equivalent of Na2S2O3 (1 mole K2Cr2O7 react with 6 moles Na2S2O3). Determination of peroxide value. Weigh 3.00 g oil (with precision of 0.001 g) into a 250 ml Erlenmeyer flask. Add 10 ml chloroform and swirl to dissolve oil. Add 15 ml acetic acid,
Zing Substances. For ionizing substances, such as NaCl , 1mosm is 1mmole times the number of ions formed when each molecule dissociates. One mmole of NaCl is 58 mg, but when it dissociates, it yields 1 mmole of Na+ (23mg) and 1mmole of Cl ( 35mg). Therefore , 58 mg of NaCl is 2 mOsm of NaCl is put into a beaker and distilled water added to make 1 liter, the osmolarity is 2mOsm/l. A) How many mosm solute will 1 gram of NaCl yield?
Measure the solution by right clicking on the beaker and choose pH meter *Then I had to measure the pH of 0.1 M sodium hydroxide Get a 100 mL beaker from the equipment menu Right click on the beaker, select chemicals, and add 50 mL of 0.1 M sodium hydroxide. Measure the solution by right clicking on the beaker and choose pH meter Part 2: *First add 35 ml of unknown acid a to 100 mL beaker. Select all chemicals from the toolbar in the chemicals section, choose unknown acid a. Put the volume at 35 mL in a new 100 mL beaker. *Then add two drops of phenolphthalein indicator to the beaker by right clicking, choosing indications, and adding 2 drops of phenolphthalein.
After heating, the mixture was cooled to room temperature and filtered by vacuum filtration into a fritted funnel to yield a purple product. The product was washed 3 times with (5mL) portions of chilled 6M HCL, then Ethanol, and lastly with acetone. The resulting product was placed into a vial and left to dry in a vacuum desiccator for 1 week and weighed the next week. The yield was 6.029g. The second experiment, procedure 1, combined [Co(NH3)5 (H2O)]Cl2 (0.0060M, 1.52g) and (25mL) of distilled water to an 125mL Erlenmeyer flask.
Why is this necessary? Obtain an appropriate amount of 5.00 M NaCl and fill your 25 mL buret. Pipet a 20.00 mL aliquot of 0.100 M acetic acid solution into a 100 mL beaker, add a magnetic stirring bar, and then set up the titration apparatus as indicated in Figure 1. Record the initial pH and then begin titrating. You will titrate in 0.25 mL intervals for the first 2 ml and then in 1 mL intervals until a total of 6 mL of 5.00 M NaCl has been delivered.
Get 200 mL sample of polluted water and place into 250 beaker 5. Record observations of polluted water into data table 6. Take 100 mL of polluted water to the water testing stations and record data 7. Place a 150 mL beaker under pipe and carefully pour the remaining polluted water into the filter 8. Record the starting time, which is the time all the water was poured in 9.
The dichloromethane is then separated from the mixture in the rotary evaporator. Figure 1: The structure of caffeine is very similar to those of purine bases (adenine and guanine) in DNA, therefore caffeine is a good substance to practice on for dealing with nucleic acids. Procedure Approximately 10g of tealeaves, CaCO3 (4.8g, 0.048 mol) and deionised H2O (100mL) is added into a beaker and boiled for 15 minutes. The mixture is then cooled to 20˚C and is filtrated using a Buchner funnel (vacuum filtration). The extraction process is when a solvent, dichloromethane (15mL) is added to the filtrate in a separatory funnel; the mixture is gently swirled together 3 times, and stopcock is released in between to vent the funnel.