After you have raised the vehicle off of the ground, you then loosen the rest of the lug nuts and begin to take the tire off. Place the lug nuts in a safe location where they wont get lost. Then take the flat tire off and put it in your trunk, while replacing it with the spare. If you are unsure which way the spare goes on, make sure the valve (small tube sticking out the tire where air is placed) is facing out. The final steps of fixing a flat tire are tightening the lug nuts by turning them clockwise until they are nice and snug.
How To Change A Tire Hello, my name is ------- -------------and I will be explaining to you on how to change a tire on your car, or truck. In this essay we will cover what tools you are going to need, how to remove your current tire, how to inspect your brakes, tire pressure and replace your tire with a new or used one. While we are in the process of doing all of this work today, it will get a little dirty. Make sure you have a rag or something close to wipe your hands with. In this first section we will make sure that we have all the tools we are going to need to change a tire.
Use a toothbrush or cotton swabs for the areas around the trigger and front sight-posts. You can also grab a can of air duster to help loosen dirt or sand in areas which the brush will not get. Next remove the hand guards from
If not, a list of supplies you will need include: emergency warning triangles, a flashlight with a stand, a jack, a spare tire, a lug nut wrench, and a torque wrench. All of which I have personally used, and believe are extremely important in being successful at changing your own tire. If your tire goes flat while driving, slowly reduce your speed and safely pull off of the roadway giving your self enough room to change your tire. This is a very important step to remember to avoid causing an accident or any more damage to your vehicle. Next, turn off your engine and engage your parking break.
If the driver doesn’t have a manual, just find the sturdiest point closes to the tire you are changing. With the jack in place, take the handle and turn the crank on the jack clock wise to start lifting the car up until the wheel is high enough off the ground to remove the tire. Once the car is off the ground, finish removing the lug nuts and place them in the hub cap. By placing the lug nuts in the hub cap, the driver will know exactly where they placed them. Remove the wheel from the vehicle placing it flat on the ground to
It is common to remove the axles from the final drive which will allow the final drive to rotate freely. Once the track is disconnected, the weight pulling on the final drive can cause the tracks to unravel on their own. The tracks should be blocked before disconnecting in order to keep the track from rotating and the machine should be raised off the ground on proper rated jackstands. Be sure to position the track links that will be removed between the final drive and the rear idler. Be sure to clean the bushings and track links before using the proper tooling for separating the track to insure the tool works properly.
A. Brakes used for parking. B. If the air brakes leak down, springs press the brakes on to stop the vehicle. C. The spring on the brake pedal.
- Make sure the Compounds are no where close to your other sensory organs, remember that only your eyes are protected by the Goggles. -If a compound is spilled, wipe it up immediately and tell the instructor. Materials : powder forms of these compounds - LiNO3 - NaNO3 - KNO3 - Ca(NO3)2 - Ba(NO3)2 - - Unknown compound A - Unknown compound B - Goggles, Bunsen burner, distilled water, Q-tips, paper towel and a striker. Procedures 1- Turn on the Bunsen burner around the 45 degree angle. 2- Feel the gas on the top of the Bunsen burner with your hands, adjust if too high or too low.
I begin by placing wheel blocks behind the rear tires on my vehicle. Next, I will find my mechanics gloves and place them on my hands. Now, I want to make sure I have the proper socket to remove the drain plug, a socket wrench, oil drain pan, and oil filter wrench. Once I have my safety equipment and proper tools. I begin by first using either a car jack or a floor jack to raise the vehicle off the ground.
If the ink you are testing does not spread out, re-test it using rubbing alcohol. 8. Repeat this process for each strip and compare your results. 9. Let the strips dry and tape them on a sheet of paper as a record of the different pen types.