Fill the burette with 0.005mol dm-3 potassium manganate(VII) solution. 6. Pour some of the thyme extract solution into a 250cm3 plastic beaker. 7. Using a measuring cylinder, add 50cm3 of 1.0mol dm-3 sulphuric(VI) acid to the thyme extract in the conical flask.
Nest one Styrofoam cup in another 11. Obtain an exact mass of tap water (45-50g) to serve as cold water 12. Put a magnetic stirrer in the bottom of the calorimeter 13. Secure temperature probe to a ring stand 14. Place temperature probe through hole in cardboard lid and position probe about 1cm above bottom of calorimeter 15.
The two unknown solids are weighed to a mass of 0.15g each. The unknown solids are dropped carefully into the corresponding Erlenmeyer flask wit 50mL of distilled water. The solid in the water must be dissolved and afterwards add 10 drops of Bromecresol green to indicate the change of color when the solution has been titrated. The flask should start with a blue tint. HCl is carefully dropped into the Erlenmeyer flasks with the primed pipette until the solution turn to a green tint.
PROCEDURE 1. Get the following equipment for your group: burette pipette syringe with piece of rubber tubing attached 1–250 mL beaker 3–100 mL beakers grease pencil stand and burette clamp Each beaker must be clean and dry. Label one 100 mL beaker “ACID”, one “BASE” and one “RINSE”. 2. Pour about 80 mL of NaOH solution into the BASE beaker.
After heating, the mixture was cooled to room temperature and filtered by vacuum filtration into a fritted funnel to yield a purple product. The product was washed 3 times with (5mL) portions of chilled 6M HCL, then Ethanol, and lastly with acetone. The resulting product was placed into a vial and left to dry in a vacuum desiccator for 1 week and weighed the next week. The yield was 6.029g. The second experiment, procedure 1, combined [Co(NH3)5 (H2O)]Cl2 (0.0060M, 1.52g) and (25mL) of distilled water to an 125mL Erlenmeyer flask.
Begin heating the water to the boiling point 3. Measure the mass of an empty, dry 18 x 150 mm test tube and record. 4. Add the sample metal pieces until the test tube is ¼ to 1/3 of the way full. Measure and record the mass of the test tube and metal.
Gravimetric Determination of Sulfate Purpose The purpose of this lab is to determine the percentage of sulfate in the hydrate by precipitating the sulfate as barium sulfate. Materials Filler paper Sodium sulfate Graduated cylinder Bunsen burner Watch glass Beakers (250 mL, 400 mL) Rubber bulb Graduated pipette Beaker tongs Funnel Filter Paper Sodium Sulfate Drying oven Wash bottle Stirring rod Silver nitrate Hydrochloric acid Distilled water Small test tube Procedures First, .4861 grams of sodium sulfate was placed into a clean 400mL beaker. Exactly 200mL of water and 1mL of HCl was added to the same beaker. A watch glass was placed on the beaker and the solution was heated using the Bunsen burner to a gentle boil. The watch glass was removed with the beaker tongs.
Using another 125-mL flask, 60-mL of 0.3622 M potassium hydroxide in ethanol was deposited. Both flasks were clamped in a temperature-controlled bath regulated at 50.0˚C. The solutions were then set in the temperature bath for ten minutes to equilibrate. An empty 250-mL Erlenmeyer flask was also clamped in the same water bath. In another flask 50-mL of ice water was deposited with three-drop phenolphthalein.
Add 0.5 ml concentrated HCl and 1.0 ml 15% KI solution. Mixed exactly 1 minute and leave for 5 minutes in a dark place. Add 0.5 ml starch solution, 20 ml distilled water. Mix and titrate with sodium thiosufate solution. Calculate the exact normality of Na2S2O3 knowing that in this chemical reaction 1 gram-equivalent of K2Cr2O7 react with 1 gram-equivalent of Na2S2O3 (1 mole K2Cr2O7 react with 6 moles Na2S2O3).
The extraction process is when a solvent, dichloromethane (15mL) is added to the filtrate in a separatory funnel; the mixture is gently swirled together 3 times, and stopcock is released in between to vent the funnel. Dichloromethane (including the emulsion) is then drained from the bottom into a 50mL Erlenmeyer flask. Same extraction process is repeated on the same filtrate and the dichloromethane is, once again, let out to the same 50mL Erlenmeyer flask as before. The combined dichloromethane solution and water (20mL) is poured into a rinsed separatory funnel. Mixture is gently swirled and drained out into an Erlenmeyer flask.