The purpose of this lab is to focus on how to make zinc iodide in a different way using compounds instead of elements, which are barium iodide and zinc sulfate. We will see if the reaction between these two compounds will occur and make a prediction by writing a chemical equation. The procedures for this lab are to place a small test tube inside a 50mL beaker and weigh it. Then, using a spatula, add 0.45±0.03 g of zinc sulfate heptahydrate into the small test tube and record the mass. After that, dissolve the sample in 2 mL of deionized water and shake the test tube for 1 to 1 ½ minutes to dissolve the solid.
Nest one Styrofoam cup in another 11. Obtain an exact mass of tap water (45-50g) to serve as cold water 12. Put a magnetic stirrer in the bottom of the calorimeter 13. Secure temperature probe to a ring stand 14. Place temperature probe through hole in cardboard lid and position probe about 1cm above bottom of calorimeter 15.
Lab 2: If we heat sand then conduction will occur. III. Materials Lab 1: * 500mL Beaker * Water * Hot Plate * 2 Thermometers * Food coloring * Stopwatch * Oven mitt Lab 2: * 500 Ml beaker * Water * Hot Plate * 2 Thermometers * Beaker of sand – about 150-200 mL * Stopwatch * Oven mitt IV. Procedure Lab 1 1. Gather all materials 2.
Fill the burette with 0.005mol dm-3 potassium manganate(VII) solution. 6. Pour some of the thyme extract solution into a 250cm3 plastic beaker. 7. Using a measuring cylinder, add 50cm3 of 1.0mol dm-3 sulphuric(VI) acid to the thyme extract in the conical flask.
SYNTHESIS 3 Purifying an unknown solid by recrystallization involved preparing cobalt amine chloride product. By adding five grams of cobalt II chloride into 20ml of 9M HBR in 250 mL beaker, plus 15 mL of deionized water. Dissolving the compound within pure water, filtration by gravity and adding two grams of activated charcoal and 25 mL of concentrated. Cooled after heating and additional six mL of 30 percent hydrogen peroxide. Filter by suction then collect the dark solid.
Using another 125-mL flask, 60-mL of 0.3622 M potassium hydroxide in ethanol was deposited. Both flasks were clamped in a temperature-controlled bath regulated at 50.0˚C. The solutions were then set in the temperature bath for ten minutes to equilibrate. An empty 250-mL Erlenmeyer flask was also clamped in the same water bath. In another flask 50-mL of ice water was deposited with three-drop phenolphthalein.
· There are numerous measures of the amount of solute in solvent. Try this exercise. Exercise 1. Devise a measure of solute concentration that you would place on the label for the following case: You weigh out 2.56 g of zinc iodide: You put the solid zinc iodide in a 500 mL flask and fill the flask with water to ttie 500-ml nia'rk. You now have sao mL of a zinc iodide aqueous solution.
Laboratory Report Chemistry Mr. Crider Title: Validating the Gas Laws Purpose: The purpose of this lab is to validate Charles’ Law, Boyle’s Law, and I deal Gas Law by attempting experiments that prove all three Kinetic Molecular Theories are in face true. Hypothesis: If the first procedure shows a fixed amount of gas at a constant will both either increase or decrease simultaneously according to Charles’s Law. If an unknown volume of air has mass in the second procedure, then it is a form of matter because of the presence of atoms. If the third procedure has a fixed amount of gas at a constant temperature, then according to Boyle’s Law the volume of the gas will increase as the pressure of the gas decrease or vice versa. Materials: Safety Goggle Laboratory Apron 60-cm3 syringe with end cap 2 utility clamps Ring stand and ring Wire gauze 600-mL Beaker Thermometer inserted into spilt stopper Bunsen Burner Air pump w/ pressure gauge Balance 1 L Graduated Cylinder (or assume syringe vol.
Liquids and Solids Purpose: The goal of this experiment is to be able to identify melting/boiling points of substances. We can then use these methods to identify unknown substances because of constants in melting/boiling points. Procedure: 1. Boiling Point a. Begin by adding 1 mL of rubbing alcohol to test tube and attach a thermometer to it.
Why is this necessary? Obtain an appropriate amount of 5.00 M NaCl and fill your 25 mL buret. Pipet a 20.00 mL aliquot of 0.100 M acetic acid solution into a 100 mL beaker, add a magnetic stirring bar, and then set up the titration apparatus as indicated in Figure 1. Record the initial pH and then begin titrating. You will titrate in 0.25 mL intervals for the first 2 ml and then in 1 mL intervals until a total of 6 mL of 5.00 M NaCl has been delivered.