Conclusion 10 Grams of Potassium chlorate when decomposed produces 3.915576 grams oxygen gas and 6.083363 grams potassium chloride Atomic Weight of Magnesium Introduction In this lab we will determine the atomic weight of magnesium by measuring the amount of hydrogen gas evolved when hydrochloric acid reacts with magnesium. The reaction is as follows: Mg + 2HCl -> H2 + Mg2+ (aq) + 2Cl- (aq) There is a one to one relationship between the number of moles of hydrogen gas evolved and the
of moles of CO2 = 72/(24 000) = 0.003 mol no. of moles of C = no. of moles of CO2 (from the formula, CO2, and the = 0.003 mol equation, C + O2 CO2) mass of C = 0.003 x 12.0 = 0.036 g mass of Al = 0.144 – 0.036 = 0.108 aluminium carbon mass (g) 0.108 0.036 molar mass 27.0 12.0 (mass )/(molar mass) = no. of moles 0.108/27.0 = 0.004 0.036/12.0 = 0.003 ratio 4 3 Hence, the empirical formula of X is Al4C3. Example
(4 points) n = 125 4. If magnesium was the limiting reactant in this lab, calculate the theoretical yield of the gaseous product. Show all steps of your calculation. (4 points) Moles of Mg: (0.0281 g)(1 mole / 24.305 g) = 1.156 x 10^-3 moles 5. Determine the percent yield of this reaction, showing all steps of your calculation.
93 g/mol? Not we get to use it! Yay! 93 g/mol / 31.06 g/mol = 3 (this is the multiplier) Multiply that whole number through the subscripts of the empirical formula. 3 x (C H5 N) = C3H15N3 Hydrated compounds Solving process: 1st- the difference between the initial mass and that of the dry sample is the mass of water that was driven off.
This reaction can be summed up using the following formula: 5Fe2++8H++MnO4- →5Fe3++Mn2++4H2O After standardization, the potassium permanganate solution is then titrated with 3 different magnesium oxalate solutions. To find the concentration of the C2O42- the balanced net ionic redox reaction formula is used: 5C2O42-+16H++2MnO4- →10CO2+2Mn2++8H2O It is important to note the addition of sulfuric acid (9M H2SO4) in performing this experiment because of the following reasons: 1) Sulfuric acid keeps the iron (II) from air oxidizing into iron (III) 2) Sulfuric acid keeps the iron (II) from hydrolyzing into Fe(OH)2 3) Sulfuric
Procedure: Refer to Chemistry Lab Manual pp. 33-35, 37. Results: The density of the yeast-sugar solution on day 1 was 1.05g/mL. On day 2, the density of the solution had dropped down to 1.00g/mL. We found the mass of our pure alcohol to be 10.23g.
This will bring your equation to look like this: 3H2O+Fe ---> FeO3+H2 The equation is not yet balanced, since we now have an uneven number of iron and hydrogen atoms. To fix this, we will put a two in front of the Fe on the left, to give you the proper number of iron atoms. Then, we will put a three in front of the hydrogen on the right, to give the proper number of all
Single Replacement Reaction Laboratory Modified from Glencoe Chemistry - Matter and Change, Glencoe McGraw-Hill, 2002 Objectives Observe a single replacement reaction Measure the masses of iron and copper Determine the mole ratios and the limiting reactant Chemicals Iron filings (Fe) – 20 mesh Copper(II) sulfate pentahydrate, (CuSO4·5H2O) Distilled water Materials Stir rod 100-mL beaker 250-mL beaker 25-mL graduated cylinder Weigh paper Balance Hot plate Beaker tongs Wire mesh insulated pad screen Distilled water wash bottles |Lab Data - Reaction of Copper(II) Sulfate and Iron | | Mass of empty 100-mL beaker |(g) | | | Mass of 100-mL beaker
Ten kilograms of oxygen and 2 kg of hydrogen are mixed in a 1 m3 vessel. The mixture is at 300K, and initially no reaction takes place. 9. What is most nearly the partial pressure of the hydrogen? A.
Abdul Gadoush Period 2 Chemistry Honors 1-16-14 Metal Gizmo 1. Purpose/Problem: The whole purpose to this experiment was to identify which metal of the following: Copper, Magnesium or zinc had the most occurring reactions in the constant chemicals that they were inserted in. The metal that had the least amount of reactions in each chemical would be the least reactant, and the metal that had the most occurring reactions in the chemical would be the most reactant. For this process to occur (make metal gizmos), Naugatuck Metal Works needs one highly reactive metal and another that isn't a reactive metal. - signs of chemical change = changes the shape and color, creates a gas, distributes heat, Etc.