In the first part, five 100 mL flasks of 5 mL ligand solution, 5 mL 2 M sodium acetate, 4 mL 3 M NH2OH, and 1-5 mL Fe2+ solution are diluted with water. The absorption spectrum for varying concentrations of Fe2+ are measured using a spectrophotometer and the data is graphed in Excel. The slope of the line is ε in the Beer-Lambart equation A = εcl. In the second part of the experiment, eleven flasks containing diluted stock solutions of Fe2+ and ligand are mixed with 5 mL 2 M sodium acetate and 4 mL 3 M NH2OH and diluted with water. The absorption spectrum is measured using a spectrophotometer and the data is graphed in Excel.
Calculate the volume of 0.250 M H2SO4 that contains 0.250 g H2SO4. 0.250 g H2SO4 x 1 mole x 1 L = 0.0102 L 98.12 g 0.250 mole 5. 1.50 g of NaCl is dissolved in 100.0 mL of water. Calculate the concentration. 6.
Gas Law Worksheet 1. A sample of gas has a volume of 1.50 L at 600 mm Hg and a temperature of 20.0° C. What would be the volume at STP? 2. Calculate the volume of 50.0 g of methane, CH4, when at a pressure of 742 mm Hg and temperature of 25.0° C. 3. A gas occupies 300.0 mL at 20.0° C. What would be its volume at 0° C, if the pressure is constant?
1 mole of water B. 2 moles of water C. 3 moles of water D. 2 moles of water with 1 mole of hydrogen left over 8. Ten kilograms of hydrogen gas (H2) are mixed with 355 kg of chlorine (Cl2) in a 0.50 m3 drum. The two gases react to produce hydrogen chloride. What is the final pressure in the drum if the final temperature is 60oC?
Thus, the molarity of the HCl solution can be calculated by dividing the number of moles of HCl by the volume of HCl (in liters) used to neutralize the Na2CO3 . Now that it is a neutralized solution, we are able to use it for the titration of NaHCO3. NaHCO3(aq.) + HCl(aq.) ==> NaCl(aq.)
c. Prepare the solution by dissolving 38.90 grams of ZnI2 with 500 mL of water. d. 0.0125/0.25 = 0.05 L = 50 mL. This produces 0.0125 moles of ZnI2 5. Exercise 5: a. (0.125)(0.1) = 0.0125 moles of solute b. Pour 50 mL of the stock solution to get the number of moles needed.
A cuvette block, four cuvettes, three 50 mL beakers, one 150 mL beaker, and one 5mL pipet were obtained. The phosphate buffers NaH₂PO₄ and Na₂HPO₄ were procured weighing .4060g and .4106g respectively. The phosphate buffers were then transported to the 150mL beaker. Next 50mL of distilled water was measured using a graduated cylinder and added to the 150mL beaker. Twenty drops of bromothymol blue was also added to the 150mL beaker.
(2 points) Mg(s) + 2 HCl(aq) → H2(g) + MgCl2(aq) 2. Determine the partial pressure of the hydrogen gas collected in the gas collection tube. (3 points) partial pressure H2 = total pressure - vapor pressure of water = 746mmHg - 19.8mmHg = 726mmHg 3. Calculate the moles of hydrogen gas collected. (4 points) n = 125 4.
The following data were obtained when a sample of barium chloride hydrate was analyzed as described in the Procedure section. Calculate (a) the mass of the hydrate, (b) the mass of water lost during heating, and (c) the percent water in the hydrate. Mass of empty test tube 18.42 g Mass of test tube and hydrate (before heating) 20.75 g Mass of test tube and anhydrous salt (after heating) 20.41 g. Mass of the Hydrate is 2.33g. Loss (H2O) is 0.34g. Percent H2O in Hydrate is equal 0.34/2.33=14.6% 3.
CaCO3 + 2HCl -----CaCl2 + CO2 + H2O ( Volume of acid added (L) ) (1.0mol/L) = moles acid added. Moles acid added - moles base added = moles acid that reacted. Moles of acid that reacted / 2 = moles CaCO3 present in sample. Final answer % CaCO3 3. Put exactly 5.0 mL of water in the 10.0 mL graduated cylinder.